SZD-24 Foka

SZD-24 Foka
SZD-32A Foka 5
Role Glider
National origin Poland
Manufacturer SZD
Designer Piotr Mynarski & Władysław Okarmus
First flight 2 May 1960
Number built 204 SZD-24 + 132 SZD-32

The SZD-24 Foka (Seal) (Szybowcowy Zakład Doświadczalny - Glider Experimental Works) was a single-seat high performance aerobatic glider designed and built in Poland in 1960.

Contents

Development

The SZD-24 Foka was designed for competition flying in the 'Standard' class as well as aerobatic flying. The design originated from a design competition within SZD which was won by the ”Delfin”, to become the SZD-24 Foka in production. The first flight, by SP-2069, took place in May 1960 at Bielsko but results were not good with poorly performing airbrakes which were unable to limit the airspeed below VNE (Velocity Never Exceed). This posed a problem as OSTIV (Organisation Scientifique et Technique Internationale du Vol à Voile – International Scientific and technical organisation for gliding) rules for the Standard class in gliding competitions stipulate that speed limiting devices must limit maximum speed to VNE or below. A second prototype was quickly built, fitted with much improved air-brakes as well as improved canopy locks and an additional access panel in the rear fuselage. Adam Zientek carried out the first flight of the second prototype on 24 May 1960 which went on to take third place in the 'Standard' class at the 1960 World Gliding Championships at Köln in Germany, piloted by Adam Witek. The SZD-24 Foka prototype was much admired for its performance, elegance, aerodynamically clean lines and comfortable semi reclined flying position. The pre-production variant, called SZD-24A, introduced more refinements and the line was steadily improved up to the SZD-32 Foka 5 final production variant. The Foka was the holder of seven world records and many Polish national records including[1]:-

Other achievements by 'Foka' aircraft include:-

After several accidents attributed to structural failure, all Foka aircraft extant have now been limited to a maximum speed of 165 km/h in clear air and 140 km/h IFR/rough air[1].

Following a fatal accident due to failure of the wing attachment mechanism in 2010 [2] and another fatal accident with a glider with similar assembly mechanism, the British Gliding Association has issued a Safety Alert for owners of Foka IV gliders [3].

Description (SZD-24-4A )

The SZD-24 Foka series were Standard class gliders of predominantly wooden construction with fixed wheel and skid undercarriage.

Fuselage

The fuselage comprised a wooden structure with the cockpit in the extreme nose transitioning with very clean lines to the integral fin at the rear. The forward opening canopy was jettisonable in case of emergency and comprising plexiglass clear portions fitted to a 'Duralumin' frame. A 300mm x 125mm mainwheel, with mechanically operated brakes connected to the airbrake lever, was fitted in a semi recessed position augmented by flush fitting skids under the nose and tail. The construction methods of the fuselage evolved throughout the series culminating in large panels, formed in concrete moulds, of plywood and PVC foam sandwich giving a very smooth finish, high strength and reduced weight. The pilot sat semi-reclined in an adjustable back-rest seat with headrest and non-adjustable rudder pedals. The instrument panel sits on a column above and between the pilots legs, with basic instruments and supplementary instruments as required. A single tow hook is fitted to the left of the nose-skid with a release control cable operated by a control knob at the base of the instrument panel. The forward sliding canopy comprised the entire top half of the forward fuselage which slid forward, on runners, controlled by a knob in a track on the left side of the cockpit rim. The canopy was constructed around a 'Duralumin' frame with 'Plexiglas' transparent section and moulded opaque nose section.

Wings

The trapezoidal wings were built up with heavy gauge moulded plywood skins, supported by wooden ribs, using NACA 63 3 618 at the root changing smoothly to NACA 4415 at the tip. Large metal plate air brakes are fitted well aft of the main spar at approximately ¾ chord, in already turbulent air flow, to reduce drag. Roll control is provided by ailerons in the trailing edges of the outer wings (the SZD-24-2 Foka 2 was fitted with reduced area ailerons to reduce drag, but rollcontrol was dramatically reduced).

Tail Unit

The sharply swept fin (used to increase control power and stability with a smaller fuselage, reducing weight), was integral with the fuselage and supported the plywood skinned tail plane at approx ⅓ fin span. The mass balanced rudder and elevators were built up from wood/plywood and fabric covered.

Surface Finish

As delivered the Foka's were given a similar surface finish, with a broad stripe,tapering from the centre-section to nose and tail, either side of the fuselage and a contrasting colour on the remainder of the fuselage. A large stylised Foka logo was added in the stripe under the cockpit. Wings were usually white with red wing tips.

Variants

Specifications (SZD-24-4A Foka 4A)

Data from http://www.piotrp.de/SZYBOWCE/pszd24.htm

General characteristics

Performance

See also

Aircraft of comparable role, configuration and era

References

External links